Schematic Diagram: single

Showing posts with label single. Show all posts

Wednesday, November 12, 2014

IC TDA7012T Mini FM Received Based on Single FM circuit with explanation

Mini FM Received Circuit

TDA7021T chip radio receiver ambit is for carriageable radios, stereo as able-bodied as mono, area a minimum of ambit is important in agreement of baby ambit and low cost. It is absolutely accordant for applications application the low-voltage micro affability arrangement (MTS). The IC has a abundance bound bend (FLL) arrangement with an average abundance of 76 kHz. The selectivity is acquired by alive RC filters.

The alone action to be acquainted is the beating abundance of the oscillator. Interstation babble as able-bodied as babble from accepting anemic signals is bargain by a alternation aphasiac system.

Part List:

R1 = 8kΩ2
R2 = 10kΩ
R3 = 390Ω
C1,C3 = 10nF
C2,C6,C9,C16 = 100nF
C4 = 33pF
C5 = 25pF trimmer (Murata type TZB4Z250AB10R00)
C7,C10 = 1nF5
C8 = 820pF C11 = 1nF
C12 = 68pF
C13 = 220pF
C14 = 47μF 10V (Nichicon UWX1A470MCL1GB 5.5mmL chip type)
C15 = 3nF3
L1 = 36nH (4 turns 0.5mm silver-plated wire, inside diameter 4mm; length 7mm)
L2 = 1μH, SMD case 0805 (fres > 300 MHz)
IC1 = TDA7021T (SMD in SO16 case)

Sunday, October 5, 2014

9 Volt 2 Amp PSU Single IC Regulator Power Supply

Notes

There is little to be said about this circuit. All the assignment is done by the regulator. The 78S09 can bear up to 2 amps connected achievement whilst advancement a low babble and actual able-bodied adapted supply.

The ambit will assignment after the added components, but for about-face polarity aegis a 1N5400 diode is provided at the input, added cutting actuality provided by C1. The achievement date includes C2 for added filtering, if powering a argumentation ambit than a 100nF capacitor is additionally adorable to abolish any aerial abundance switching noise.

Saturday, August 23, 2014

Single Supply Instrumentation Amplifier

The OP284 is a low noise dual op amp with a bandwidth of 4MHz and rail-to-rail input/output operation. These properties make it ideal for low supply voltage applications such as in a two op amp instrumentation amplifier as shown in the diagram. The schema uses the classic two op amp instrumentation topology with four resistors to set the gain. The transfer equation of the schema is identical to that of a non-inverting amplifier. Resistors R2 and R3 should be closely matched to each other as well as to resistors (R1+P1) and R4 to ensure good common-mode rejection (CMR) performance. It is advisable to use resistor networks for R2 an and R3, because these exhibit the necessary relative tolerance matching for good performance.

Potentiometer P1 is used for optimum d.c. CMR adjustment, and capacitor C1 is used to optimize a.c. CMR. With schema values as shown, schema CMR is better than 80 dB over the frequency range of 20 Hz to 20 kHz. Circuit referred-to-input (RTI) noise in the 0.1 Hz to 10 Hz band is exemplary at 0.45 µVpp. Resistors R5 and R6 protect the inputs of the op amps against over-voltages. Capacitor C2 may be included to limit the bandwidth. Its value should be adjusted depending on the required closed-loop bandwidth of the schema. The R4-C2 time constant creates a pole at a frequency, f3dB, equal to f3dB=1/2πR4C2. With a value of C2 of 12 pF, the bandwidth is about 500 kHz. The amplifier draws a current of about 2mA.