Music On Hold for Telephones

Here is a simple schema for music-on-hold with automatic shut off facility. During telephone conversation if you are reminded of some urgent work, momentarily push switch S1 until red LED1 glows, keep the telephone handset on the cradle, and attend to the work on hand. A soft music is generated and passed into the telephone lines while the other-end subscriber holds. When you return, you can simply pick up the handset again and continue with the conversation. The glowing of LED1, while the music is generated, indicates that the telephone is in hold position. As soon as the handset is picked up, LED1 is turned off and the music stops.

Circuit diagram :

Music-On-Hold for Telephones Circuit Diagram

Normally, the voltage across telephone lines is about 50 volts. When we pick up the receiver (handset), it drops to about 9 volts. The minimum voltage required to activate this schema is about 15 volts. If the voltage is less than 15 volts, the schema automatically switches off. However, initially both transistors T1 and T2 are cut off. The transistor pair of T1 and T2 performs switching and latching action when switch S1 is momentarily pressed, provided the line voltage is more than 15 volts, i.e. when the handset is placed on the cradle. Once the transistor pair of TI and T2 starts conducting, melody generator IC1 gets the supply and is activated. The mu-sic is coupled to the telephone lines via capacitor C2, resistor R1, and the bridge rectifier.

With the handset off-hook after a ring, momentary depression of switch S1 causes forward biasing of transistor T2. Mean-while, if the handset is placed on the cradle, the current passing through R1 (connected across the emitter and base terminals of pnp transistor T1) develops enough voltage to forward bias transistor T1 and it starts conducting. As a consequence, output voltage at the collector of transistor T1 sustains for-ward biasing of transistor T2, even if switch S1 is released. This latching action keeps both transistors T1 and T2 in conduction as long as the output of the bridge rectifier is greater than 15 volts. If the handset is now lifted off-hook, the rectifier output drops to about 9 volts and hence latching action ceases and the schema automatically switches off.

EFY lab note. The value of resistor R2 determines the current through resistor R1 to develop adequate voltage (greater than 0.65 volts) for conduction of transistor T1. Hence it may be test selected between 33 kilo-ohms and 100 kilo-ohms to obtain instant latching.) The total cost of this schema is around Rs 50.

Author : SIBIN K. ZACHARIAH - Copyright : Electronicsforu

Clap Switch Wiring diagram Schematic

Clap Switch Circuit Diagram. Here’s a clap switch free from false triggering. To turn on/off any appliance, you just have to clap twice. The schema changes its output state only when you clap twice within the set time period. Here, you’ve to clap within 3 seconds. 

The clap sound sensed by condenser microphone is amplified by transistor T1. The amplified signal provides negative pulse to pin 2 of IC1 and IC2, triggering both the ICs. IC1, commonly used as a timer, is wired here as a monostable multivibrator. Trigging of IC1 causes pin 3 to go high and it remains high for a certain time period depending on the selected values of R7 and C3. 

This ‘on’ time (T) of IC1 can be calculated using the following relationship: T=1.1R7.C3 seconds where R7 is in ohms and C3 in microfarads. On first clap, output pin 3 of IC1 goes high and remains in this standby position for the preset time.Also, LED1 glows for this period. The output of IC1 provides supply voltage to IC2 at its pins 8 and 4.

Clap Switch  Circuit diagram :

Clap Switch Circuit Diagram

Now IC2 is ready to receive the triggering signal. Resistor R10 and capacitor C7 connected to pin 4 of IC2 prevent false triggering when IC1 provides the supply voltage to IC2 at first clap. On second clap, a negative pulse triggers IC2 and its output pin 3 goes high for a time period depending on R9 and C5.

 This provides a positive pulse at clock pin 14 of decade counter IC 4017 (IC3). Decade counter IC3 is wired here as a bistable. Each pulse applied at clock pin 14 changes the output state at pin 2 (Q1) of IC3 because Q2 is connected to reset pin 15. The high output at pin 2 drives transistor T2 and also energizes relay RL1. LED2 indicates activation of relay RL1 and on/off status of the appliance. A free-wheeling diode (D1) prevents damage of T2 when relay de-energizes.

Fog Lamp Sensor Wiring diagram Schematic

For several years now, a rear fog lamp has been mandatory for trailers and caravans in order to improve visibility under foggy conditions.

Circuit diagram :

Fog Lamp Sensor Circuit Diagram

When this fog lamp is switched on, the fog lamp of the pulling vehicle must be switched off to avoid irritating reflections. For this purpose, a mechanical switch is now built into the 13-way female connector in order to switch off the fog lamp of the pulling vehicle and switch on the fog lamp of the trailer or caravan. For anyone who uses a 7-way connector, this switching can also be implemented electronically with the aid of the schema illustrated here.

Here a type P521 optocoupler detects whether the fog lamp of the caravan or trailer is connected. If the fog lamp is switched on in the car, a current flows through the caravan fog lamp via diodes D1 and D2. This causes the LED in the optocoupler to light up, with the result that the phototransistor conducts and energises the relay via transistor T1. The relay switches off the fog lamp of the car.

For anyone who’s not all thumbs, this small schema can easily be built on a small piece of perforated schema board and then fitted somewhere close to the rear lamp fitting of the pulling vehicle.