Showing posts with label inverter. Show all posts
Showing posts with label inverter. Show all posts

Saturday, October 18, 2014

1 5v to 9v INVERTER

This very clever circuit will convert 1.5v to 9v to take the place of those expensive 9v batteries. But the clever part is the voltage regulating section. It reduces the current to less than 10mA when no current is being drawn from the output. You can use two or three old cells for the supply and the circuit will totally use up all the energy from the cells. Its a great circuit for using up those old cells. With a 470R load, the output current is 20mA and the voltage drop is less than 10mV. It is best to use 3 old cells as this will deliver about 2.5v to 3v and the circuit will produce an efficiency of about 70%. Adjust the 15k resistor for 9v.

source : http://www.talkingelectronics.com.au/projects/200TrCcts/200TrCcts.html
Read More..

Thursday, October 2, 2014

100 watt Compact Ferrite Inverter Circuit

A very small and compact ferrite based 100 watt inverter circuit can be built using around the IC 4047 which has an internal oscilator.
The proposed inverter circuit utilizes a small ferrite transformer for acquring the required 220V mains AC.

This 100 watt compact ferrite inverter is just like other like inverter circuits but is compaxct by neture since theres no heavy or bulky transformer used in this design.

The block diagram for the same may be understood as folows:

A 4047 IC is used for geting the bsic oscillations required for any inverter design.

Referring to the given circuit, two 4047 stages could be seen for the required actions.

The upper 4047 IC is riged as a high frequency oscillator, the given should be adjusted to acquire around 60kHz frequency over the connected mosfets.

Once initiated the mosfets conduct in a push-pull manner inducing the entire battery volatge and current across the primary winding of the associated ferrite E core transformer TR1.

As per th winding configuration, the transformer generaters an equivalent amount of voltage, thats around 220 + 220V across the secondary center tap winding or the output winding.

The lower 4047 IC stage is configured as a 50 Hz oscillator.

Here its pin13 is used as the output for driving a P/N pair of mosfets. These mosfets again conduct in a push pull manner, however since a p/n pair is used, unlike the upper stage here it conducts to produce both the cycles of AC output.

This stage is integrated with the points A and B of the upper 220+220V points, which is appropriately push and pulled alternately by the p/n pair to produce a 220V AC across the shown points at exactly 50 Hz.

The design is a simple 220V square wave type, which could be sutiably modified for getting a sine wave output.



The coil or the main transformer maybe wound on suitable EE type core which may accomodate the following winding data comfortably:

Primary = 6-0-6 number of turns using 1mm diameter super enameled coper wire.

Secondary = 350-0-350 turns using 0.3mm super enameled copper wire
Read More..

Wednesday, September 3, 2014

DELL E1909WDD 19 LCD Color Monitor SMPS and Back light Inverter Troubleshooting

Dell E1909WDD - 19" LCD Color Monitor Power Supply and Backlight Inverter – Troubleshooting & Schematics 
[CLICK ON THE PICTURES TO MAGNIFY]
POWER SUPPLY (SMPS) SCHEMATIC 
NO POWER - TROUBLESHOOTING

BACK-LIGHT INVERTER SCHEMATIC
NO BACK-LIGHT _ TROUBLESHOOTING
PWB

Read More..

Thursday, August 28, 2014

6 to 12 Volt Power Supply Inverter

This inverter circuit can provide up to 800mA of 12V power from a 6V supply. For example, you could run 12V car accessories in a 6V (British?) car. The circuit is simple, about 75% efficient and quite useful. By changing just a few components, you can also modify it for different voltages.



Read more
Read More..

Tuesday, August 26, 2014

Simple Low Cost 100W Inverter

Here is the schema diagram of a simple 100 watt inverter using IC CD4047 and MOSFET IRF540. The schema is simple low cost and can be even assembled on a veroboard. Circuit diagram : Simple Low Cost 100W Inverter Circuit Diagram CD 4047 is a low power CMOS astable/monostable multivibrator IC. Here it is wired as an astable multivibrator producing two pulse  trains of 0.01s which are 180 degree out of phase at the pins 10 and 11 of the IC. Pin 10 is connected to the gate of Q1 and pin 11 is connected to the gate of Q2. Resistors R3 and R4 prevents the loading of the IC by the respective MOSFETs. When pin 10 is high Q1 conducts and  current flows through the upper half of the transformer primary which accounts for the positive half of the output AC voltage. When pin 11 is high Q2 conducts and  current flows through the lower half of the transformer primary in opposite direction and it accounts for the negative half of the output AC voltage.

Notes.

  •     B1 can be  a 12V/ 6Ah lead acid battery.
  •     Q1 and Q2 must be fitted to a proper heat sink.
  •     T1 can be a 9-0-9 V primary, 230V secondary, 150VA transformer .
  •     Do not expect much from this schema. The is very simple one suitable for low grade applications.

Read More..

Sunday, August 24, 2014

Power Mosfet Inverter Wiring diagram Schematic

This Power Mosfet Inverter Circuit Diagram can deliver .high-voltage ac or dc, with a rectifier and filter, up to several hundred volts. The secondary and primary of T1-a 12.6 to 440 V power transformer, respectively-are reversed; e.g., the primary becomes the secondary and the secondary becomes the primary. Transistors Q1 and Q2 can be any power FET. Be sure to heat sink Q1 and Q2. Capacitors C1 and C2 are used as spike suppressors. 

 Power Mosfet Inverter Circuit Diagram


Power
Read More..

Wednesday, August 20, 2014

500W Low Cost 12V to 220V Inverter Wiring diagram Schematic

Attention: This Circuit is using high voltage that is lethal. Please take appropriate precautions

Using this schema you can convert the 12V dc in to the 220V Ac. In this schema 4047 is use to generate the square wave of 50hz and amplify the current and then amplify the voltage by using the step transformer.

How to calculate transformer rating

The basic formula is P=VI and between input output of the transformer we have Power input = Power output

For example if we want a 220W output at 220V then we need 1A at the output. Then at the input we must have at least 18.3V at 12V because: 12V*18.3 = 220v*1

So you have to wind the step up transformer 12v to 220v but input winding must be capable to bear 20A.


500W
Read More..

Tuesday, August 19, 2014

12V to 220V Inverter Schematics

12V to 220V Inverter Circuit Diagrams, Even though today’s electrical appliances are increasingly often self-powered, especially the portable ones you carry around when camping or holidaying in summer, you do still sometimes need a source of 230 V AC - and while we’re about it, why not at a frequency close to that of the mains? As long as the power required from such a source remains relatively low - here we’ve chosen 30 VA - it’s very easy to build an inverter with simple, cheap components that many electronics hobbyists may even already have 12V to 220V Inverter.
inverter
12V to 220V Inverter Circuit Diagrams
Though it is possible to build a more powerful circuit, the complexity caused by the very heavy currents to be handled on the low-voltage side leads to circuits that would be out of place in this summer issue. Let’s not forget, for example, that just to get a meager 1 amp at 230 VAC, the battery primary side would have to handle more than 20 ADC!. The circuit diagram of 12V to 220V Inverter Schematics our project is easy to follow. A classic 555 timer chip, identified as IC1, is configured as an astable multivibrator at a frequency close to 100 Hz, which can be adjusted accurately by means of potentiometer P1.

As the mark/space ratio (duty factor) of the 555 output is a long way from being 1:1 (50%), it is used to drive a D-type flip-flop produced using a CMOS type 4013 IC. This produces perfect complementary square-wave signals (i.e. in antiphase) on its Q and Q outputs suitable for driving the output power transistors. As the output 12V to 220V Inverter current available from the CMOS 4013 is very small, Darlington power transistors are used to arrive at the necessary output current. We have chosen MJ3001s from the now defunct Motorola (only as a semi-conductor manufacturer, of course!) which are cheap and readily available, but any equivalent power Darlington could be used.

These drive a 230 V to 2 × 9 V center-tapped transformer used ‘backwards’ to produce the 230 V output. The presence of the 230 VAC voltage is indicated by a neon light, while a VDR (voltage dependent resistor) type S10K250 or S07K250 clips off the spikes and surges that may appear at the transistor switching points. The output signal this circuit produces is approximately a square wave; only approximately, since it is somewhat distorted by passing through the transformer. Fortunately, it is suitable for the majority of electrical devices it is capable of supplying, whether they be light bulbs, small motors, or power supplies for electronic devices.

PCB layout:
  COMPONENTS LIST
Resistors
R1 = 18k?
R2 = 3k3
R3 = 1k
R4,R5 = 1k?5
R6 = VDR S10K250 (or S07K250)
P1 = 100 k potentiometer
Capacitors
C1 = 330nF
C2 = 1000 µF 25V
Semiconductor
T1,T2 = MJ3001
IC1 = 555
IC2 = 4013
Miscellaneous
LA1 = neon light 230 V
F1 = fuse, 5A
TR1 = mains transformer, 2x9V 40VA (see text)
4 solder pins

Note that, even though the circuit is intended and designed for powering by a car battery, i.e. from 12 V, the transformer is specified with a 9 V primary. But at full power you need to allow for a voltage drop of around 3 V between the collector and emitter of the power transistors. This relatively high saturation voltage is in fact a ‘shortcoming’ common to all devices in Darlington configuration, which actually consists of two transistors in one case. We’re suggesting a PCB design to make it easy to construct this project; as the component overlay shows, the PCB only carries the low-power, low-voltage components.

The Darlington transistors should be fitted onto a finned anodized aluminum heat-sink using the standard insulating accessories of mica washers and shouldered washers, as their collectors are connected to the metal cans and would otherwise be short-circuited. An output power of 30 VA implies a current consumption of the order of 3 A from the 12 V battery at the ‘primary side’. So the wires connecting the collectors of the MJ3001s [1] T1 and T2 to the transformer primary, the emitters of T1 and T2 to the battery negative terminal, and the battery positive terminal to the transformer primary will need to have a minimum cross-sectional area of 2 mm2 so as to minimize voltage drop.

The transformer can be any 230 V to 2 × 9 V type, with an E/I iron core or toroidal, rated at around 40 VA. Properly constructed on the board shown here, the circuit should work at once, the only adjustment being to set the output to a frequency of 50 Hz with P1. You should keep in minds that the frequency stability of the 555 is fairly poor by today’s standards, so you shouldn’t rely on it to drive your radio-alarm correctly – but is such a device very useful or indeed desirable to have on holiday anyway? Watch out too for the fact that the output voltage of this inverter is just as dangerous as the mains from your domestic power sockets.

So you need to apply just the same safety rules! Also, the project should be enclosed in a sturdy ABS or diecast so no parts can be touched while in operation. The circuit should not be too difficult to adapt to other mains voltages or frequencies, for example 110 V, 115 V or 127 V, 60 Hz. The AC voltage requires a transformer with a different primary voltage (which here becomes the secondary), and the frequency, some adjusting of P1 and possibly minor changes to the values of timing components R1 and C1 on the 555.
B. Broussas
Source : Link

Another interesting related Circuit : DC 12V to 24V Contverter, 5000W PWM inverter, and other Inverter / Converter Circuit.
Read More..

Saturday, August 16, 2014

DC to AC Inverter with 555 Wiring diagram Schematic

This schema is more of a DC to AC inverter, it uses a 555 IC as a low frequency oscillator, adjustable, adjustment can be done by the potentiometer R4 and frequency should be between 50-60 Hertz. The pulses from the IC 555 will go to Q1 and Q2 are amplified and sent to the transformer T1, which has its winding reversed. Capacitor C4 and coil L1 filter are the input to T1, it effectively ensures that a sine wave is formed.

 DC to AC Inverter with 555 Circuit Diagram

DC


List of components

R1 = 10K
R2 = 100K
R3 = 100 ohms
R4 = 50K potmeter
C1, C2 = 0.1μF
C3 = 0.01μF
C4 = 2700μF
Q1 = TIP41A, NTE196, ECG196
Q2 = TIP42A, NTE197, ECG197
L1 = 1μH
T1 = Transformer
Read More..

Voltage Inverter using IC NE 555

In many diagram we need to generate an internal adjustable voltage. This schema shows how it is possible to use a trusty old NE555 timer IC and a bit of external schemary to create a voltage inverter and doubler. The input voltage to be doubled is fed in at connector K1. To generate the stepped-up output at connector K2 the timer IC drives a two-stage inverting charge pump schema.

The NE555 is configured as an astable multivibrator and produces a rectangular wave at its output, with variable mark-space ratio and variable frequency. This results in timing capacitor C3 (see schema diagram) being alternately charged and discharged; the voltage at pin 2 (THR) of the NE555 swings between one-third of the supply voltage and two-thirds of the supply voltage.

Voltage Inverter Circuit Using IC NE555 


Voltage Inverter Circuit Using IC NE555

The output of the NE555 is connected to two voltage inverters. The first inverter comprises C1, C2, D1 and D2. These components convert the rectangular wave signal into a nega-tive DC level at the upper pin of K2. The second inverter, comprising C4, C5, D3 and D4, is also driven from the output of IC1, but uses the negative output voltage present on diode D3 as its reference potential. The consequence is that at the lower pin of output connector K2 we obtain a negative volt-age double that on the upper pin.


Now let us look at the voltage feedback arrangement, which lets us adjust this doubled negative output voltage down to the level we want. The NE555 has a control voltage input on pin 5 (CV). Normally the voltage level on this pin is maintained at two-thirds of the supply voltage by internal schemary. The voltage provides a reference for one of the comparators inside the device. If the reference voltage on the CV pin is raised towards the supply voltage by an external schema, the timing capacitor C3 in the astable multivibrator will take longer to charge and to discharge. As a result the frequency of the rectangle wave output from IC1 will fall, and its mark-space ratio will also fall.

The source for the CV reference voltage in this schema is the base-emitter junction of PNP transistor T1. If the base volt-age of T1 is approximately 500 mV lower than its emitter voltage, T1 will start to conduct and thus pull the voltage on the CV pin towards the positive supply.

In the feedback path NPN transistor T2 has the function of a voltage level shifter, being wired in common-base configuration. The threshold is set by the resistance of the feedback chain comprising resistor R3 and potentiometer P1. When the emitter voltage of transistor T2 is more than approximately 500 mV lower than its base voltage it will start to conduct. Its collector then acts as a current sink. Potentiometer P1 can be used to adjust the sensitivity of the negative feedback schema and hence the final output voltage level.Using T1 as a voltage reference means that the schema will adjust itself to compensate not only for changes in load at K2, but also for changes in the input supply voltage. If K2 is disconnected from the load the desired output voltage will be maintained, with the oscillation frequency falling to around 150 Hz.

A particular feature of this schema is the somewhat unconventional way that the NE555’s discharge pin (pin 7) is connected to its output (pin 3). To understand how this trick works we need to inspect the innards of the IC. Both pins are outputs, driven by internal transistors with bases both connected (via separate base resistors) to the emitter of a further transistor. The collectors of the output transistors are thus isolated from one another [1].

The external wiring connecting pins 3 and 7 together means that the two transistors are operating in parallel: this roughly doubles the current that can be switched to ground.The two oscilloscope traces show how the output voltage behaves under different circumstances. The left-hand figure shows the behaviour of the schema with an input voltage of 9 V and a resistive load of 470 Ω connected to the lower pin of output connector K2. The figure on the right shows the situation with an input voltage of 10 V and a load of 1 kΩ on the lower pin of output connector K2. The pulse width and frequency of the rectangle wave at the output of IC1 are automatically adjusted to compensate for the differing conditions by the feedback mechanism built around T1 and T2.

Because of the voltage drops across the Darlington out-put stage in the IC (2.5 V maximum) and the four diodes (700 mV each) the schema achieves an efficiency at full load (470 Ω between the output and ground) of approximately 50 %; at lower loads (1 kΩ) the efficiency is about 65 %.

Author : Peter Krueger -  Copyright : Elektor
Read More..

Wednesday, August 13, 2014

Switching inverter for 12v Systems Wiring diagram Schematic

This is a simple Switching inverter for 12v Systems Circuit Diagram. This PWM control schema provides the control pulse to the DMOS Power Switch in the fly back schema. The output of the PWM is a pulse whose width is proportional to the input control voltage and whose repetition rate is determined by an external clock signal. To provide the control input to the PWM and to prevent the output voltage from soaring or sagging as the load changes the error amplifier and reference voltage complete the design. They act as the feedback loop in this control schema much like that of a servo control system. 

Switching inverter for 12v Systems Circuit Diagram


Switching inverter for 12v Systems Circuit Diagram

Read More..